Features:
1、Support 51 STM8S STM32 and other microcontroller development boards. 2、The module is nRF24L01P + PA + LNA and its driving method is exactly the same as nRF24L01P. Users can operate according to the nRF24L01P chip manual. 3、The CE pin is connected to the LNA enable pin. When CE = 1, the LNA is turned on. When CE = 0, the LNA is turned off. This operation is identical to the transmit and receive modes of the nRF24L01. In other words, the user does not need to care about the operation of the LNA at all. 4、The CE can be connected high for a long time, but the module must first be set to the POWER DOWN power-down mode when writing to the register. It is recommended to connect the CE to the IO port of the MCU. The IRQ can be disconnected and the interrupt status can be obtained using the SPI polling mode. However, it is recommended to use an external interrupt from the microcontroller. 5、The module's CE pin timing operation can reach the 10us mentioned in the nRF24L01P technical manual, but we recommend changing it to: SPI operation until CE goes high until the transmit interrupt is completed, then keep 1ms high time, then Lower the CE. The purpose is to switch to receive mode immediately after sending the GT-24. If CE = 0, the LNA is turned off, which will adversely affect the receiving sensitivity.
Specification:
Item Type:Wireless Module
Type:Direct Insert/Patch Mounting(Optional)
Serial number
product name
parameter
Summary
1
model
GT-24
————
2
RF solution
nRF24L01P
————
3
Module size
30.3 x 14.5mm / 1.19 x 0.57in
PCB antenna included
4
Working frequency
2.4GHz-2.525GHz
Adjustable, 1MHz step
5
Production Process
Lead-free environmentally friendly process
Machine stickers, products must be machine-mounted to ensure consistent batch reliability
6
Interface mode
1*8*1.27mm/2*4*2.54mm
The patch can also be used with the universal board and line.
7
Supply voltage
DC: 2.0-3.6V
Note: Voltages above 3.6V will cause permanent damage to the module.
8
Communication level
0.7VCC-3.3V
VCC refers to the module supply voltage
9
Measured distance
1000m
Clear and empty, maximum power, height 2m, 250K air speed
10
Transmit power
4 levels adjustable up to 20dBm
About 100mW at maximum power
11
Air speed
250K-2Mbps
Level 3 adjustable (250Kbps, 1Mbps, 2Mbps)
12
Shutdown current
About 30uA
Test conditions: CE=0, power down mode, VCC=3.0V
13
Emission current
About 90mA
Power supply capacity must be greater than 250mA
14
Receiving current
About 20mA
CE=1
15
Antenna form
PCB antenna / ipex carrier antenna
————
16
Communication Interface
SPI
High speed power up to 10Mbps
17
Launch length
Single packet 1-32 bytes
3-level FIFO
18
Receiving length
Single packet 1-32 bytes
3-level FIFO
19
RSSI support
not support
Only simple packet loss statistics are supported
20
Receiving sensitivity
-B2294dBm@250Kbp
————
21
Operating temperature
-40~+85°C
Industrial grade
22
Working humidity
10%-90%
Relative humidity, no condensation
23
Storage temperature
-40~+125°C
---
Package List:
1 x Module1 x Pin Header
Notes:
Notice the grounding is good, the paving area is large, and the power supply ripple is small. The filter capacitor should be added as close as possible to the VCC and GND pins of the module.
Teslim edilmediğinde para iadesi
